Technical Resource Hub

Dictate the summary of this article: Your browser does not support the audio element. Digital signage can now be displayed using a web browser. The Web Player is on a view-only basis, so you can't make config changes on the screen itself. To use the web player you need to open the url link within the same server tenant. For example, on your Dashboard:However, when you switch to View:It will switch to:As you can see, it has switched from UK1B to UK1S, but you never leave your GoBright portal. In this instance, if you was to use UK1B the browser will alway show an activation code (valid for 12 months). However, when switching to UK1S the digital signage kicks in - as long as you have added the device on the GoBright portal.Please check the correct link on your GoBright portal as GoBright has several servers across different countries. In this instance, Ascentae is on UK1B, so it's UK1S. The full link for this example would be:https://uk1s.gobright.cloud/playerAscentae have tested this on the following browsers:                  Browser                        Version     Test Result     Approved?Chrome148.0.7778.179 (64-bit)👍🏻   YesEdge148.0.3967.83 (64-bit)👍🏻   YesFireFox151.0.2 (64-bit)👍🏻   YesOpera132.0.5905.11 (64-bit)👍🏻   YesSafari11.1 or higher(Tested by GoBright)   YesBrave1.90.124 (64-bit)👍🏻   YesWe tested the above in June 2026.Please ensure you are running the latest release of your browser.Lets Get StartedLogin to your GoBright portal at https://portal.gobright.cloudSelect the 4-square grid in the top-right and select 'View'Select the 'Devices' tab and look for the top level location. In this instance, there is just one. Right-click on the location and select Add > DeviceOn this page, enter a relevant name and hit saveYou will then be directed to a new page Now we need to activate your device. The activation code is shown on screenEnter your activation code & allow around 1 minute for the activation to kick-inIf you want to read the full GoBright article, it can be found here.If you have any questions, please log a support ticket.

The Control Plug is the solution for managing the power usage for your GoBright Interact. The solution is to power on your desk workstation only when checked-in.Summary, key points & benefits:Supports a Bluetooth range of up to 15mUp to 5 Interacts can be connected to a single Control PlugThe firmware version on the Interact must be running 2.4.7 or aboveOnly available for Interacts - GoBright Connects are not supportedAvailable in UK, EU and USA versionsEnergy Savings: Automatically cuts power to desk peripherals (monitors, docking stations, etc.) when the desk is not in use, reducing your impact on the environmentBy requiring a check-in to activate power, it ensures more reliable desk occupancy data for facility managersClick here to view the extensive installation guide from GoBright to get up and running.

Product Code: INT1-POE-DESKGoBright have released a PoE adapter for their Interact device. If you can't power the device over the 230V mains adapter, PoE is now here! As you can see, it comes with 3M adhesive to fix the device to a surface.This is the connection that needs to be plugged into the Interact device:You then have the expansion box:  Note: A network cable is not suppliedWe tested the device on the 12th of June 2024, using a "dumb" NETGEAR PoE switch and an Interact running Application Version 1.6.1. If you're using a managed switch, please ensure PoE is enabled on the port(s) that you connect the Interact(s) to. Some further photos that might help plan your installation:Important: When using Interacts, you must configure your firewall to allow outbound traffic over MQTT (port 8883) over TLS. NTP and DNS must also be correctly configured for the device to communicate with the GoBright platform. The firewall configuration can be found here.Please contact support@ascentae.com for any help.

If the device powers up as expected, but is stuck on the Android boot screen, please follow these steps to re-flash (factory reset) the ProDVX panel. You will need to re-install the relevant booking app after performing the following steps.Unplug everything from the device, including the power source.Press and hold the "Volume +" button.Whilst holding this button, provide power to the device (can be both PoE or PSU).Keep holding the button until the Android Recovery menu appears. In this menu, navigate using the volume (+/-) buttons to the format/wipe system option.Select this option by long pressing the circular menu button next to it.After confirming the reset, reboot the device and check and confirm whether it does so without any issues.After step 7, please be patient as it can take up to 10 minutes for the panel to reload. When the process is complete, you'll have a blank Android panel. As this process completely resets the panel, you'll need to reconfigure the network - so if you're using Wi-Fi you will need to re-authenticate.If you have any further questions, please contact support@ascentae.com to log a support ticket. It helps to speed things up if you provide:ModelSerial NumberProof of Purchase

In Q1 of 2026 GoBright rolled out an overhaul of their process when ordering catering to a room booking. We like the new design, it's much smoother!In the update: A fresh, clean & clearer overview of your entire orderImproved efficency for user experienceIf you have ordered this as part of your commissioning package, Ascentae will get everything set up for you. This Includes: Service Providers - email notifications at a specified time prior to the meetingA catalog of itemsCategories - food / drink / room layouts etcCost centresImportant: Service licenses are added on a per-room basis. Please calculate how many rooms you will need to enable catering for and discuss this with your Ascentae account manager.An example of how this can look:You can always arrange a demo with your Ascentae account manager to see the process in action!

Here's a simple guide to factory resetting your GoBright Interact.With a small screwdriver or a paperclip you can press the reset button for 5-10 seconds.Let the device fully reboot. You'll then need the GoBright app to scan the QR code shown on screen and link the Interact to the relevant desk / room.The GoBright app is available for free on both Apple and Android devices. Just check out your relevant app store and search for 'GoBright'.