Technical Resource Hub

Dictate the summary of this article: Your browser does not support the audio element. Digital signage can now be displayed using a web browser. The Web Player is on a view-only basis, so you can't make config changes on the screen itself. To use the web player you need to open the url link within the same server tenant. For example, on your Dashboard:However, when you switch to View:It will switch to:As you can see, it has switched from UK1B to UK1S, but you never leave your GoBright portal. In this instance, if you was to use UK1B the browser will alway show an activation code (valid for 12 months). However, when switching to UK1S the digital signage kicks in - as long as you have added the device on the GoBright portal.Please check the correct link on your GoBright portal as GoBright has several servers across different countries. In this instance, Ascentae is on UK1B, so it's UK1S. The full link for this example would be:https://uk1s.gobright.cloud/playerAscentae have tested this on the following browsers:                  Browser                        Version     Test Result     Approved?Chrome148.0.7778.179 (64-bit)👍🏻   YesEdge148.0.3967.83 (64-bit)👍🏻   YesFireFox151.0.2 (64-bit)👍🏻   YesOpera132.0.5905.11 (64-bit)👍🏻   YesSafari11.1 or higher(Tested by GoBright)   YesBrave1.90.124 (64-bit)👍🏻   YesWe tested the above in June 2026.Please ensure you are running the latest release of your browser.Lets Get StartedLogin to your GoBright portal at https://portal.gobright.cloudSelect the 4-square grid in the top-right and select 'View'Select the 'Devices' tab and look for the top level location. In this instance, there is just one. Right-click on the location and select Add > DeviceOn this page, enter a relevant name and hit saveYou will then be directed to a new page Now we need to activate your device. The activation code is shown on screenEnter your activation code & allow around 1 minute for the activation to kick-inIf you want to read the full GoBright article, it can be found here.If you have any questions, please log a support ticket.

Dictate the summary of this article: Your browser does not support the audio element. Initial Configuration - Setting SSIDWhen configuring your MAXHUB host device (V-series screen or W70) for use with the WB05 wireless dongle, an SSID must be configured.  By default, the SSID will populate with the device name you have entered during the initial setup.However, whilst the device name can contain punctuation, the SSID cannot.  If the SSID contains punctuation, when you pair the dongle and attempt to use it on your computer, the dongle cannot connect to the host device.How to FixFollow these steps to resolve the issueExit from the home screen of the host device (if it is a W70, you need to break out of the MTR interface using admin credentials)Go to the Windows desktop and load 'Settings' appNavigate to 'Wireless Hotspot' menuEnsure 'Wireless Hotspot' is enabledChange 'Hotspot Name to remove any punctuationExit appReboot deviceOnce device has rebooted, insert the dongle into the USB port on the device to re-pair the dongleUsing the Wireless DongleThe effective range of the wireless dongle is 4m from the centre of the screen.Performance will be impacted at extreme range,  Symptoms may includeLoss of connection between dongle and host deviceDelayed screen refreshLagging of video / audioLoss of sync between video and audioMaximum range can be impacted if the screen is recessed, the MTR is mounted behind a screen or the is no 'line of sight' between the host device and the dongle.If any of these issues occur, relocate the sharing computer and dongle closer to the host device.

Wi-Fi signal strength is measured in dBm, with values usually ranging from -30 dBm to -90 dBm. A value closer to 0 (e.g. -50 dBm) indicates a stronger, faster connection, while lower numbers (e.g. -80 dBm) indicates a weaker, slower, or unstable connection. -50 dBm to -60 dBm (Excellent/Good)-60 dBm to -70 dBm (Fair)-70 dBm to -80 dBm (Weak)-80 dBm to -90 dBm (Unusable)Walls and electronic interference will significantly drop the dBm value in your environment. Finding your dBm level on an InteractPress and hold the time in the top-right for a few secondsSelect open device infoHere you have 4 options on the left hand side. On this screen you can find:StatusIP addressMAC addressSSID Signal, channel and dBmAuth mode used (e.g WPA2 PSK)We need to concentrate on the 2nd option down - WiFi. There is a signal indicator that will fluctuate in real-time. Values between -50 dBm and -65 dBm are good.Important: Interacts operate on the 2.4 Ghz spectrum. 5 Ghz is not supported.Still having issues? Check out our on site install guide here.

This article has moved. Please click here to view the guide.

When commissioning Interacts on site, these can only be commissioned via the GoBright App. Here's your initial quick checklist:✅ An Interact ✅ An admin account for the GoBright Portal ✅ A smartphone with the latest GoBright mobile app, logged in as an admin✅ An Interact profile (this is done the on portal)✅ If the devices sit behind a firewall, please ensure MQTT over TLS has been correctly configured.Please note: When using Wi-Fi:✅ 2.4 Ghz (supported)❌️ 5 Ghz (not supported)Now that all of the above are in place, please follow steps 1 to 3 on this article.Related Article:Hard-reset a GoBright Interact The full firewall rules can be found here.